VUKAR dol starter not working guide

DOL Starter Makes No Click When You Press Start

Mohit Vekaria

When a DOL starter is not working and pressing Start produces no click, first record whether the panel shows power, whether it is in the correct mode and whether a fault or external interlock is active. In a conventional contactor starter, silence suggests the contactor never picked up, but the sound alone cannot tell you whether the coil lost its command, control power is missing, or the contactor itself has a problem. Start with information you can collect from outside the closed panel.

Separate a silent start from two similar symptoms

On a traditional direct-on-line starter, the contactor is the switch that closes the main power contacts when its coil is energised. A click often marks that movement. A panel may also contain other relays that make a sound, so a click from behind a closed door is an observation. The technician uses the panel drawing and status indications to establish which device operated.

What you notice What it helps the technician establish
No click or running indication Follow control power, start command and permissives up to the contactor output.
One click but motor stays still Confirm which device clicked and whether the motor power path was established.
Click while Start is pressed, then release when the button is let go Look at how a momentary command is retained, or how the controller withdraws the command.

A permissive is a condition the panel needs before it accepts a start request. A closed stop circuit, healthy overload contact or external process signal can play that role. The conditions depend on the actual panel. In a pump installation an external level control may be involved. In a conveyor the permission could come from another machine. The DOL starter power and control diagram explains where the two paths split. Keep that distinction in mind while describing the symptom.

Three different symptoms
Three different symptoms. Report what occurred and when so the technician can trace the right circuit. · Open full-size visual

Five observations to make at the closed panel

  1. Read the front display and lamps. Write exactly what you see, including a dark display. A lit screen establishes that its own supply is present. Other branches of the control circuit may still be interrupted.
  2. Record the selected mode. If the machine is in Remote or Auto, a local Start button may have a different role from the same button in Local. Photograph the selector position and note where the request came from.
  3. Record any fault or inhibit before resetting. The exact text, time and preceding operation are more helpful than a note that says the panel showed an error.
  4. Check the process from outside the enclosure. For a pump, note tank levels, whether the installation is calling for water, and whether a programmed delay is shown on the front interface. Follow the operating instructions for the equipment.
  5. Write what changed. A recent outage, panel replacement, motor service or controller change gives the technician a starting point. Include the last known successful run.

Ask anyone nearby to report their own observation separately. “It was silent at 08:10 when I pressed Start” and “the display was blank after the evening power cut” can both be true. Putting both notes in time order avoids testing for a condition that has already changed.

What the front panel shows
What the front panel shows. Collect the selector and display observations from outside the closed enclosure. · Open full-size visual

Example: the panel has power, but the pump stays silent

In an illustrative installation, a pump had run from a remote command the previous afternoon. The next morning the operator found the panel display lit. Pressing the front button produced no sound. The selector was in Remote, the tank was below its normal start level, and a new external controller had been installed the evening before. This record gives the technician a reason to inspect command ownership and the remote interface first.

That example does not identify a failed coil. If the external controller had never sent a valid request, the starter would have had no reason to energise its output. Conversely, a recorded remote request with an inactive contactor output moves the investigation toward an inhibit, the output stage or its wiring. The value of the example is the difference between water is needed and the starter received a valid command. Both are worth documenting.

For a VUKAR three-phase DOL installation, identify the exact model from the panel label. VUKAR distinguishes timer, auto-switch and level-control functions across its product range. Use the VUKAR three-phase DOL comparison to identify the family, then consult its exact guide. The VUKAR technical support page lists the details to collect when a fault or settings question comes up.

How a technician narrows the control path

A technician works from the exact wiring drawing and identifies the source that feeds the command circuit. A conventional example may have a control fuse, an emergency stop or normal stop path, an overload contact, a selector and the coil. A digital panel may handle commands through inputs, firmware and a relay output. A drive or programmable controller can add more permissives. The drawing and the exact panel manual take priority over the generic sequence.

There are three useful questions. First, is the control supply available for the relevant branch? Second, has the starter received a valid start command with the required conditions satisfied? Third, did the command produce the expected output at the switching device? Each answer narrows the next step. Schneider Electric’s TeSys DOL starter range illustrates how equipment selection and documentation are specific to a product family. An electrician can compare the installed parts and drawing to the actual equipment before deciding which item needs work.

Panel access and diagnostic measurements belong to a qualified person following the site's isolation, verification and electrical safety procedures. Multiple feeds can be present. An external controller can still issue a start command, and a stopped pump can still have energy in its pipe system. Site procedures should account for every relevant energy source before maintenance. See the OSHA hazardous energy control overview for the general principles behind isolation and verification.

DOL Start control circuit trace
DOL Start control circuit trace. Use the numbered path to locate the control supply, Stop contact, overload, external permission and Start contact. During the Start request these conditions must let the K1 coil energize. The installed drawing may show a separate holding or controller circuit. Open full-size diagram. Technical reference.

What to send with a service request

Send a photo of the closed panel front and its accessible model label, the motor nameplate details, the display text, mode and command source. Add the time of the last good run, what happened when Start was pressed, and any event that preceded the first failure. If someone already reset an overload or changed modes, record the action and the new result. Keep the original observation in the same message.

Here is an example of a useful service note. “08:10, pump requested from the panel. Display lit, Local selected, no audible contactor pickup and no motor movement. The pump last ran yesterday at 18:20. An external switch was replaced overnight. The display showed the attached screen before any reset.” Add which pump the panel controls if several are installed in the same room.

If the machine depends on a remote station, ask the operator there for the timestamp of the start command. A request that appears on one screen may be inhibited at another controller. Two timestamps and the exact screen names make it easier to review the sequence without repeating the failed start. The best first report describes what happened and what stayed unchanged during that attempt.

VUKAR DOL starter selection · DOL power and control circuit diagram

Report a silent start
Report a silent start. Keep a time record with the exact indication, mode and equipment identification. · Open full-size visual

Use the display history to separate today's event from an older fault

When the panel has a history screen, distinguish an active fault from an entry stored yesterday. Record the display state at the time of the failed start and list the age of any history entry if shown. A past overload can be useful background, but it may not describe this silent attempt. An active inhibit shown while the command is present gives the service team a more direct lead. Photograph the normal operator screen without clearing entries.

Another useful check is whether all local controls are affected. If a status button or screen continues to respond while Start alone has no effect, document which controls remain usable. If the entire interface went dark, write whether the change affected this one panel or other equipment in the room. The two observations give very different boundaries for the initial investigation.

Make a small timeline for faults that appeared after a power interruption. Start with the last verified run, then record the outage, the return of supply and the first requested start. A clock on a controller can be wrong after service. Keep your watch time and the panel time distinct if they disagree. That helps match electrical and process logs without assuming the events occurred together.

If the panel drives more than one pump, identify the selected pump and whether the other unit had a demand. Automatic alternation can make an otherwise healthy unit remain idle while the system assigns the job elsewhere. The service team should get the observed selection and demand indicators together. Avoid changing the rotation order just to see whether the silent panel starts.

Back to blog

Leave a comment

Please note, comments need to be approved before they are published.