VUKAR dol starter forward reverse guide

Forward/Reverse DOL Starter: How the Interlocks Work

Mohit Vekaria

A DOL starter forward reverse arrangement uses two contactors to run a compatible three-phase motor in either direction. The forward contactor applies one phase order. The reverse contactor applies a different phase order by exchanging two phases in the designed power circuit. The electrical and mechanical interlocks keep both contactors from closing together. The motor, the machine and the risk assessment determine when a direction change is permitted.

Picture a short conveyor that feeds boxes to a packing station. Forward moves boxes toward the station. An approved reverse mode may help an operator clear material after the process comes to a stop. The starter supplies the chosen direction. A complete machine design also accounts for guards, local controls, stopping behavior and what can happen if someone selects reverse while another person is working nearby.

Follow the two paths in the drawing

Begin with the power circuit. Look for the forward contactor, usually named K1 or F, and the reverse contactor, often K2 or R. The drawing for the installed panel is the authority on labels. The drawing shows how the supply reaches the motor through either contactor and where overload and short-circuit protection are provided. A maintained sequence on the forward path produces one direction. The reverse path changes the phase order.

Follow the control circuit separately. It decides which contactor coil can energize. A forward command and a reverse command enter separate branches. Both branches are generally subject to the relevant stop and protective permissives. In a typical electrical interlock, each branch also passes through an auxiliary contact from the opposite contactor. The VUKAR DOL power and control diagram explains how the branches of a basic one-direction starter work.

Forward/reverse DOL power wiring
Forward/reverse DOL power wiring. Follow L1, L2 and L3 through each contactor. K1 sends them to U, V and W in order. K2 swaps L2 and L3 before the common overload. The mechanical interlock prevents both contactors from closing together. Open full-size diagram. Technical reference.

What the two interlocks actually do

Interlock What it acts on What to identify
Electrical Control permission to energize the opposite coil The opposing contactor’s auxiliary contact or a documented control design with the intended equivalent function
Mechanical Physical movement of the contactor mechanisms The manufacturer-approved interlock device or reversing assembly for the exact contactor family

In a typical hardwired circuit, when forward is engaged, its normally closed auxiliary contact opens the reverse control branch. Reverse remains unavailable until forward releases and other permissives are satisfied. The reverse contactor has an equivalent auxiliary contact in the forward branch. Electrical design also needs to address competing commands from different locations, such as a pushbutton and a remote control station.

The mechanical interlock links the contactor mechanisms. It adds a physical barrier to simultaneous operation. Schneider Electric’s control panel guide shows TeSys reversing assemblies and explains how electrical interlocking can supplement the mechanical interlock. Use the ordering data and assembly instructions for the selected series. Schneider Electric control panel guide.

A pilot lamp is an indication. Confirm what turns it on. One design can light a lamp from a direction request, while another lights it from auxiliary feedback. An operator who sees a green lamp needs to know whether it means the control asked for forward or the contactor returned a forward signal. A technician may need separate evidence of the machine’s actual motion.

Forward/reverse electrical interlock wiring
Forward/reverse electrical interlock wiring. Each coil has the opposite contactor’s NC auxiliary in series and its own NO auxiliary across Start. With K1 energized, K2’s path is open at K1 aux NC. Stop drops the active coil. Confirm that the machine has stopped before changing direction. Open full-size diagram. Technical reference.

A stopped command and a stopped machine are different observations

When forward is released, the contactor can drop out before the machine has finished coasting. A conveyor with a heavy load or a fan with a large wheel can keep moving. A reversing command may therefore need a separate standstill condition or a validated delay. Have the responsible designer determine the method. An ordinary contactor auxiliary indicates contactor state and gives limited information about shaft speed.

Example: a conveyor controller records that the forward contactor released quickly after Stop, but the belt kept moving for several seconds. The designer reviews the actual coast time across load conditions, specifies the necessary direction-change permissive and tests it. The service record should preserve the observation and the approved control response. Copying an arbitrary delay from another machine makes the inspection harder because the load and stopping behavior can differ.

For a simple reversible process, ask whether the operator needs momentary jog, a maintained direction selection or a deliberate second press after Stop. These are separate control decisions. Identify what the machine should do when it loses power, when it regains power and when a fault is reset while a remote run request is still present.

Before a direction change
Before a direction change. Follow the machine’s specified stop and standstill requirements before a new command. · Open full-size visual

What a service visit should separate

  • Forward works and reverse is unavailable. Record which command was issued, the state of the displayed permissives, and whether forward contactor feedback cleared after Stop.
  • Direction lamp changes while movement stays the same. Find whether the lamp follows the command or the feedback. Have the technician compare observed motion with the approved drawing.
  • The motor changes direction after supply service. Tell the electrician what changed at the supply and whether both commands now run opposite to the labels.
  • The load moves unexpectedly after a reset. Keep the equipment out of service pending assessment of the maintained commands, reset and restart behavior.

A forward contactor may release mechanically while an auxiliary used for the opposite interlock fails to return. The operator’s report that forward stopped is useful, but it is only the beginning of the diagnosis. Record the command, the feedback, the machine movement and the displayed fault separately. A timestamped account will help the technician decide whether to examine the command branch, the contactor assembly or the upstream supply first.

Design for the second control station

One practical problem appears when the same machine has pushbuttons at the panel and a second station at the other end of the line. People can issue competing requests. The specification should explain which station has control, how the operator can see that selection and what happens if someone changes mode during a run. Put these choices on the control drawing and operating instructions. The technician can then test what the two stations do together.

A programmable controller can manage a direction request and report a mismatch between command and feedback. The machine designer still determines the hardwired interlocks and any safety-related control functions required by the application. If the design calls for feedback from a specific auxiliary contact, include the correct part and contact assignment on the bill of materials. Record the behavior expected if a signal remains active when it should have cleared.

Request a test at the operator station where the labels are used. A service engineer may be able to read F and R at the panel while the operator can only see arrows at the conveyor. Compare the two indications during the same trial and write down any difference before the machine returns to normal use.

Where to use a standard DOL panel

Many water pumps are specified to run in a single direction. If you are choosing a starter for a pump, start with its nameplate and the desired control function. VUKAR’s three-phase digital DOL range provides model-specific options such as timer, auto switch and water-level control. Those features should be selected from the published model details. Ask for a verified reversing design when forward and reverse are requirements. VUKAR three-phase DOL panel comparison.

Single-phase motors can use different winding and starting arrangements. Their direction-control requirements come from the motor manufacturer’s connection diagram. The three-phase example here does not transfer automatically to them. For a broad introduction to starter choices, see the VUKAR motor starter types guide.

Collect these details before requesting a quote

Provide the motor nameplate, machine description, supply, required forward and reverse duties, expected starts per hour and the environment around the panel. Describe how the machine stops under the heaviest expected load. State who can command each direction, from which station and in which modes. Ask the panel builder to identify the exact contactor pair, interlocks, protection combination and control drawing.

Have the responsible technician verify the direction labels, interlock behavior, normal stop, applicable safety stops, feedback and restart conditions under an approved commissioning procedure. For a site with several identical-looking machines, place the machine ID on both the drawing and the completed test sheet. That identifies the assembly if a replacement is needed later.

One practical handover record has four columns: operator command, contactor feedback, observed movement and whether the expected stop or direction condition occurred. Fill in one row for forward, one for reverse and one for a refused direction change. Add the responsible technician’s name and date. It gives the next shift a concrete record of what the completed system was designed to do.

Direction test record
Direction test record. Record the expected command, confirmed feedback and observed direction separately. · Open full-size visual
Back to blog

Leave a comment

Please note, comments need to be approved before they are published.