DEV-P1 pump starts and stops frequently

Pump Keeps Starting and Stopping? DEV-P1 Cyclic Timer and Fault Checks

Mohit Vekaria

If a DEV-P1 pump starts and stops frequently, record RUN, the pause between starts and the three-phase display at each stop. DEV-P1 is a cyclic auto switch. Compare a complete cycle with a short one and write down what the starter, motor and water delivery each did.

Start with what the display shows

Visible state What it can mean and what to do
Pump stops near the expected end of RUN Time actual RUN and the next pause. A match with the approved cyclic values points toward normal rest. A stop at a different time with a changed display gives the electrician a separate event to review.
The display suggests operation, but water is absent The command and water delivery are separate observations. Note whether the motor actually ran and whether water reached the usual outlet. Report the first missing response. In a supervised return to service, confirm both the motor response and steady delivery.
An unfamiliar indication, an unexpected stop or a visible trip Record the exact characters or lights, the time and the motor state from outside the closed enclosure. Leave protection values as commissioned. If the stop repeats or a breaker has tripped, leave further operation to a qualified electrician.

Start with the installed unit

Record the model and revision from the label, the motor nameplate and the active mode. Similar panels can have different menus. Use the installed revision’s guide for any setting, its units and the behavior of the selected mode.

DEV-P1 RUN and rest · Start with the three visible observations. RUN and rest · Three-phase display · Starter response
Start with the three visible observations. RUN and rest · Three-phase display · Starter response

Time the stops and the starts separately

Write three times for a watched cycle. Note when the motor actually starts, when it actually stops and when it starts again if permitted. Calculate RUN from the first two and the pause from the second and third. A second start before you expected it can be as informative as an early stop. Also note whether the water reached the outlet and whether it weakened before the motor stopped.

Compare observed time with saved RUN and rest. If both match and there is no fault indication, ask whether the intended duty cycle simply looks too frequent to the operator. If either duration differs, record the display and any power interruption or other control action that preceded it. An electrician can compare the sequence with the selected mode and the motor maker’s operating limits before changing a timer or investigating a protection stop.

A worked example · DEV-P1

Suppose an early-morning run completes at its approved time and water stays steady. Later, a run stops early and the displayed supply or current state changes. Put each run in its own line, including the actual pause and whether the starter operated. A qualified electrician can use the difference to investigate supply, sensing or the starter circuit. Leave phase measurement and any changes to the protection values to them.

DEV-P1 product details

Choose RUN and RST from the water supply

RUN is the elapsed pump-on time. RST is the planned pause between cyclic runs in the selected mode. Choose RUN based on how long the source can deliver a steady flow, the space available where the water goes, and the motor maker’s permitted operating conditions. For RST, consider how long the source needs to recover and any minimum time between starts for the motor.

To estimate starts per hour during an uninterrupted cycle, add RUN and RST in minutes and divide 60 by the total. For example, 10 minutes on and 20 minutes off gives about two planned starts per hour. These are example values. Include any separate starts from other controls, power recovery or fault recovery when the installer reviews the motor’s actual start frequency.

Change one condition between watched tests

Begin a test with the mode and relevant settings written down. Change one approved timing or operating condition at a time with the installer. Then observe the pump from the start permission through the actual stop. If two settings change together, a normal or unexpected result is harder to explain later.

DEV-P1 RUN and rest · Compare the expected sequence with what happened. RUN and rest · Three-phase display · Starter response
Compare the expected sequence with what happened. RUN and rest · Three-phase display · Starter response

Keep supply events separate from the timer

On this three-phase model, a supply or phase-protection indication is a separate event from the end of a scheduled run. Record the indication as it appeared, its time and whether the pump was already running. A missing or unstable phase can require qualified diagnosis even when other equipment nearby has power. The electrician can compare the incoming supply, phase sequence and the installed protection settings against the approved record.

A changed indication can help the electrician decide where to measure. It cannot identify which wire or connection needs work. Keep the panel closed and leave tests of phase voltage, sequence and current to a qualified person. If the pump stops repeatedly or the breaker trips, leave further operation to the electrician. Give them the model, the motor nameplate and the exact time of the event.

Follow the auto switch to the starter

Treat the auto switch and the motor as separate points in the record. If the installed control circuit permits a start, the starter still has to act and the motor has to run. An indicator on the auto switch shows the state available at that device. It does not tell you everything that happened at the starter or the pump.

Write the auto switch model and the starter model on the same service note. If a command was visible, record the time. On the next line write what you could safely observe at the motor and then when water reached the outlet. An electrician can use the first missing response to identify where to work. Leave control-circuit testing, sensor changes and motor protection settings to them.

Follow the command to the pump

A controller can show a request while the motor is still off. A starter switches motor power when the control circuit permits it. Observe the display, the starter’s visible response and water delivery as separate facts. These observations give the electrician a place to start without asking you to open the enclosure or touch conductors.

If the display shows that the pump should be running but there is no water, write down whether you could see or hear the motor run from a safe location. If the motor runs but delivery is absent or weak, record how long it ran and when the flow changed. Keep the display photo and the times together so the installer can compare them with the actual settings.

Record what happens after an interruption

An automatic restart can have several conditions. If power returns, a permitted start may depend on the mode, restart settings and normal protection conditions. Some configurations also retain earlier timing information. Use the revision guide and ask the installer to explain the behavior for the mode you actually use. Keep the area around the pump and moving parts clear during supervised testing.

If the pump was waiting before an interruption, write down the time of the interruption, the display after power returned and the actual next start if it occurred. Ask the installer to record how a normal cyclic rest differs from a fault recovery wait. Leave restart settings at the approved values until the behavior is understood and tested.

Read the protection indication with the operating record

For overload, note the moment the motor stopped and whether it had reached normal running speed. The configured current response can flag a motor, supply or setup problem. For dry run, record whether water reached the outlet and when delivery weakened. An electrician can compare those events with the installed protection setup and water source.

For a voltage indication, record the time and any interruption you observed. Copy the exact characters on the display. Ask the electrician to use the instructions for the installed revision to identify the indication and decide on recovery. If the fault repeats, leave further operation to the electrician.

DEV-P1 RUN and rest · Keep the display, timing and motor response in one record.
Keep the display, timing and motor response in one record.

Send the installer one usable event record

Use the exact model and revision at the top of your note. Add the symptom and the active operating mode. On the next line, put the actual clock time, elapsed motor time if known, the visible indication and the water condition. State what you expected in the same note. If a detail could not be observed safely, leave it blank and tell the electrician.

Avoid resetting first and trying to reconstruct the event later. The display, tank condition or rest period can change once the equipment is stopped or power returns. If the electrician authorizes another watched test, agree on the expected start and stop in advance and keep the same model record. If a breaker trips, a protection indication returns or the panel appears damaged, leave further operation to the electrician.

DEV-P1 RUN and rest · Use this list for a supervised observation.
Use this list for a supervised observation.

Model instructions and service

Back to blog

Leave a comment

Please note, comments need to be approved before they are published.