VUKAR dol starter won't stop guide

DOL Starter Won’t Stop: Is the Run Command Still Active?

Mohit Vekaria

When a DOL starter won't stop, first establish whether the motor is still being powered. Water still coming out of a pipe, a lamp that stays lit and a shaft that takes time to slow down can each outlast the stop command. A motor that continues to drive its load needs a different response. Keep people clear, follow the site's emergency procedure and have authorised personnel isolate the equipment. Leave the starter out of service until a qualified technician has found the cause and tested the stop function.

What kept going after you pressed Stop?

The most helpful detail you can give the technician is what happened in the seconds after you pressed Stop. A pump may keep sending water briefly because pressure remains in the pipe or water is flowing back through it. A fan may turn in the moving air. A conveyor can coast. In a guarded installation, note what you can safely see or hear from the normal operating position. Use a trusted speed display or installed motor-current reading if the machine provides one. Keep covers and guards closed.

A contactor is the switch that carries power to the motor. Its coil is the part that pulls the contacts closed when it receives a control command. In a conventional direct-on-line starter, pressing the normal Stop button interrupts that command. The contactor should release, its main contacts should open and the machine should reach the stopping condition its design calls for. Our DOL power and control diagram guide shows the two circuits side by side.

Make a note of the sign you saw, then say what it was connected to if you know. “The green lamp stayed on” is useful. “The motor was still energised” is a stronger claim and needs evidence. A lamp driven by a controller can indicate that a run command exists. A lamp driven by auxiliary feedback reports something different. Either lamp can mislead if its circuit has a fault. That is why the panel drawing and a description of the load's movement matter together.

Separate a command that stays on from a contactor that stays closed

A technician needs to establish two states during the failed stop. Was the contactor coil still receiving the command to run? Did the main switching path actually open? Those two questions lead to different investigations. The checks depend on the exact drawing, the site procedure and the equipment design. Your operating notes can preserve the clues without putting you near live conductors.

Ways to sort a failed stop
Observation Question it raises Evidence to keep
The motor continues to drive the load after Stop Is the coil still being commanded, or did the main switching path stay closed? Mode, source of Stop and any separate command or feedback indications.
The motor comes to rest, then starts again Did a second command arrive from a timer, float or remote system? Time between stop and restart and which demand was still present.
The motor slows but water or a shaft still moves Is there coast-down, stored pressure or a separate source of motion? Direction of movement, duration and installed feedback if available.

In the first case, a stop button fault is one possibility. A remote interface can also continue to demand a run, or a control change can leave a maintained input active. In an installation with a selector, the selected mode determines which commands apply. A control drawing and the intended behaviour agreed at commissioning help identify what the machine was meant to do when Stop was used in that mode.

If the coil command drops and the load still receives power, the main contacts need attention. Contact damage or a stuck mechanism can prevent proper opening. A separate feed or wiring fault also has to be ruled out where the design makes that possible. An auxiliary indication alone cannot settle the question. Schneider Electric's motor control centre troubleshooting guide lists contact welding or freezing as a fault and points to underlying issues that need examination before parts are replaced.

DOL Stop circuit and motor power path
DOL Stop circuit and motor power path. Start at the upper control circuit and see what opens when Stop is pressed. The dashed link shows the coil operates the K1 main contacts below. Compare coil command, actual contactor response and whether the load coasts or receives power again. Open full-size diagram. Technical reference.

A stop followed by another start leaves a different record

Consider a transfer pump connected to a float and a time schedule. The operator presses Stop in local mode, the pump comes to rest and then starts ten seconds later. The useful detail is the ten-second gap. It gives the technician a reason to look for a fresh run request and compare its timing with the programmed sequence. A pump that drove continuously through the entire event sends the technician back to the command and switching states during the first stop.

A remote run request can be held by a float, pressure switch or controller output. When such a request stays true, one design waits for a deliberate re-enable and another can make a new attempt as part of its approved sequence. Identify which equipment sent the request and whether the machine stopped in the first place. One field note that captures both events is worth more than a video showing only the motor running again.

VUKAR's product catalogue lists the TPM-A as a three-phase digital DOL starter panel with auto switch and cyclic timer. It is one example of a panel whose running behaviour depends on the application and its configuration. Use the exact model documentation when asking which indication corresponds to an automatic request. VUKAR's guide to automatic pump restart explains why a return of power and a renewed demand deserve separate entries in the fault record.

Continuous run or new start?
Continuous run or new start?. A genuine pause changes what the technician needs to investigate. · Open full-size visual

What the operator can write down with the panel closed

  • The time of the stop request and the command you used, such as a panel button, remote station or controller screen.
  • The selected operating mode and any visible run demand, status message, alarm or trip code.
  • Whether the motor continued at working speed, slowed down, or reached rest and then restarted.
  • Whether a timer, float, pressure switch or upstream controller was asking for the motor to run, based on available indicators.
  • The panel model, the machine drawing revision if known and any recent repair or change to the control logic.

Write one line for the command and a second for the observed response. “14:07, Auto, pressed panel Stop” and “Pump current indication stayed present and pressure held” are more specific than “starter failed.” Use only information already displayed at the normal operating position. A technician can arrange any required measurements under the site's electrical safety procedure.

VUKAR TPM-A — Identify the TPM-A front panel
Identify the TPM-A front panel. The exact model and front-panel indication give the technician a starting point. · View the product specifications

Ask whether the failure is tied to one operating mode

Suppose the panel responds to Stop in local mode but the same button has no effect when a building controller is in charge. Preserve the exact mode and button names. An operator may assume that a local button has priority because it is mounted on the door. The documented command rules and the machine design determine its actual role. The technician can compare the as-built drawing with the agreed control sequence and identify whether the behaviour reflects a failed input, a logic change or a stop control that was never intended for that operating mode.

If the failure first appeared after a relay or controller was replaced, record the old and new part numbers and the date of the work. This gives the service team a defined change to investigate before it starts replacing parts that were already working.

What should happen before the machine goes back into service?

The repair needs to answer why the stop request failed. If the command remained active, the technician can test the accepted stop controls in each applicable operating mode. If the switching path failed to open, the repair should address the failed part and the conditions that damaged it. The technician needs the manufacturer's ratings and site records to choose a replacement. A contactor of the same physical size can have a different electrical rating.

Ask the responsible person to record the post-repair tests. A useful record identifies each stop station or screen used, the selected mode, the observed motor response and any new start request sent afterwards. For machinery with a safety function, the responsible specialist should validate it according to the machine design. An ordinary Stop command and the equipment isolation procedure have different jobs. An operator button is a control input. The OSHA hazardous-energy standard gives a clear example of the distinction between a control device and an energy-isolating device.

Put the drawing, the fault record and the verified stop test with the panel service notes. The next person should be able to see which event was a failed stop, which event was a fresh start and what changed before the panel was handed back.

Record a failed stop
Record a failed stop. Observe from the normal operator position and keep guards and covers closed. · Open full-size visual
Back to blog

Leave a comment

Please note, comments need to be approved before they are published.