Two enclosed motors on a workshop bench

How Many Amps Does a 1 HP Motor Draw? Single-Phase and Three-Phase Examples

Mohit Vekaria

A 1 HP motor's running current depends on voltage, phase, efficiency, power factor and actual load. In one worked single-phase example, 230 V, 75% efficiency and 0.80 power factor give about 5.4 A at 1 HP shaft output. A separate three-phase example at 415 V, 80% efficiency and 0.80 power factor gives about 1.6 A. These are calculated examples; the current printed on your motor's nameplate is the relevant reference for that motor.

One mechanical horsepower is about 746 W of shaft output. Electrical input must also cover the motor's losses. The label “1 HP” therefore does not mean that the motor always takes exactly 746 electrical watts or draws a fixed number of amps.

Compare examples with all assumptions visible

Calculated running-current examples at 1 mechanical HP shaft output
Supply and assumed motor data Calculation Estimated current
Single-phase, 230 V, efficiency 75%, PF 0.80 746 ÷ (230 × 0.75 × 0.80) 5.4 A
Single-phase, 230 V, efficiency 70%, PF 0.75 746 ÷ (230 × 0.70 × 0.75) 6.2 A
Balanced three-phase, 415 V, efficiency 80%, PF 0.80 746 ÷ (1.732 × 415 × 0.80 × 0.80) 1.6 A

The assumptions are chosen to explain the calculation. They are not typical-current promises, test results or specifications for a VUKAR starter or any pump brand. The examples represent different assumed motors and are not an efficiency comparison between two real products.

Use the correct HP-to-amps formula

For a single-phase AC motor, estimated running current is I = HP × 746 ÷ (V × efficiency × power factor). Enter efficiency and power factor as decimals: 75% becomes 0.75.

For a balanced three-phase motor, use I = HP × 746 ÷ (1.732 × line-to-line V × efficiency × power factor). This gives an estimated line current at the stated shaft output and operating assumptions.

If the manufacturer's nameplate uses kW, use that stated output value rather than force a rounded HP conversion. If electrical input kW is already known, do not divide it by motor efficiency again.

The existing motor output, input power and current calculator performs these steps with your own inputs.

Two enclosed motors with their nameplate areas highlighted
Check the actual motor’s nameplate to confirm its rated current.

What does the nameplate current tell you?

The rated current belongs to a defined voltage, frequency, load and motor design. Two 1 HP motors can have different nameplate amps. ABB's nameplate guide explains how full-load amps, efficiency and power factor relate to rated conditions.

A motor running below full load can draw a different current from its rated full-load value. A normal-looking amp reading alone does not confirm that the pump is delivering the required water or that every electrical condition is healthy.

Starting current is a separate check

The table estimates running current. Starting behaviour depends on the motor and starting method. Do not use the calculated running amps as a starting-current value or an automatic breaker selection.

An electrician checking a three-phase installation should consider the readings on all phases and the supply conditions. A single reading taken at an unknown moment is a weak basis for changing protection settings.

What if the current seems too high?

Record the motor nameplate, actual supply voltage, operating water conditions, fault indication and when the high reading occurs. Ask the electrician to check the starting circuit and electrical conditions, and the pump technician to check the hydraulic and mechanical load.

Do not increase an overload setting simply to prevent a trip. Use the exact relay or controller instructions together with the motor data. The overload-setting guide explains that process.

Can current tell me the electricity bill?

Amps alone cannot give an accurate AC electricity bill. You also need voltage, phase, power factor and running time, or measured real input power. The pump electricity cost calculator helps once input power and the tariff are known.

Sources and useful documents

Back to blog

Leave a comment

Please note, comments need to be approved before they are published.