VUKAR dol starter with emergency stop guide

DOL Starter Emergency Stop: What the Panel Design Must Account For

Mohit Vekaria

When a machine needs a DOL starter with emergency stop, specify the safety function before selecting the panel components. Record which motion must stop, what condition must follow the stop, how the operator resets the device and what permits the next start. A standard Start and Stop circuit controls routine operation. An emergency stop is a machine safety function that must be designed and validated for the hazards of the particular installation.

Describe the hazard the operator needs to stop

Begin at the machine. A conveyor can carry material into a dangerous zone. A pump can keep a pressurised process moving. A machine may have several drives and stored energy that remains after an electrical command is removed. Record which equipment an emergency stop is intended to affect and where an operator may need to reach it. The designer then has something specific to assess.

In a DOL starter, a contactor switches power to the motor when the control circuit commands it. The VUKAR DOL power and control diagram guide illustrates the normal starter circuit. An emergency stop design must account for how the actual machine stops, including what would happen if a relevant component failed. The normal control drawing helps identify the power and command paths. The safety design needs its own requirements and validation.

Ask the machine designer to state the scope in words you can check on the shop floor. “Stops motor M1” is useful, but it can leave out a feeder, another drive or a pressure source that also affects the hazard. “Stops the conveyor and prevents a fresh start until reset and a deliberate Start command” is a clearer statement for that example. The full specification still needs to account for the actual machine, its guards and associated equipment.

Define the stop span
Define the stop span. Identify which equipment and hazards the emergency-stop function must address. · Open full-size visual

Routine Stop, emergency stop and isolation have different jobs

Commands and states to specify
Function Purpose in the installation Record for handover
Normal Stop Ends an ordinary run under the machine's control sequence. Which controls can request it and what they do in each mode.
Emergency stop Initiates the designed response to a hazardous situation. Which equipment responds and what happens before another start is possible.
Energy isolation Secures relevant energy sources for servicing under the site procedure. Isolation points, stored energy and the responsible personnel.

A pushbutton may request a stop while the equipment still contains dangerous electrical or mechanical energy. Servicing has a separate isolation procedure. The OSHA hazardous-energy standard is a useful reference for this distinction. Follow the applicable local requirements and site procedures. The machine designer must also address guards and other safeguards that are needed for normal use.

The physical action of a machine determines whether opening a contactor immediately produces the required stopping condition. A moving load can coast or move under gravity. A pump system can retain pressure. Ask the designer to identify the expected stopping behaviour and any energy that remains after it. Siemens explains stop categories and safety system design in its Safety Integrated application manual.

VUKAR TPM-A — Ordinary motor control panel
Ordinary motor control panel. Identify the starter before specifying a separate safety function for the machine. · View the product specifications

Separate resetting the button from commanding a start

The operator needs to understand what happens when the emergency stop is reset. Pilz's guidance on ISO 13850 emergency stop reset explains that resetting the emergency stop prepares the machine for restart. The reset action by itself must not start the machine. A separate, deliberate action is needed for restart, subject to the applicable design requirements.

Consider a transfer pump with an automatic level request. The tank is still low while the emergency stop remains active. During commissioning, the design team should verify what happens to that stored or maintained request when the device is reset. The operator's expectation is clear if the machine stays in its specified stopped state until the deliberate restart action occurs. The team should document how the system handles the still-active level demand.

This question applies to any second source of a run command. A timer may still be inside its scheduled period. A remote controller may retain an output after a brief interruption. A local selector may be left in Auto. List the active modes in the specification and define what the next permitted action is after reset. If a panel builder and a machine builder are different organisations, identify who supplies the logic and who validates the complete machine.

Reset and restart are separate
Reset and restart are separate. Reset restores readiness. A separate intentional command is required to restart. · Open full-size visual
DOL emergency-stop safety architecture
DOL emergency-stop safety architecture. Two NC channels feed the safety relay. The relay monitors reset and contactor feedback before allowing its outputs. Reset restores permission. The machine’s separate deliberate Start controls restart. Select and validate the architecture for the machine’s risk assessment. Open full-size diagram. Technical reference.
Two-channel E-stop wiring at the safety relay
Two-channel E-stop wiring at the safety relay. This Siemens 3SK1 example shows the input section. One normally closed E-stop contact goes between T1 and IN1, and the other goes between T2 and IN2. Use the exact Siemens model diagram for the rest of the safety circuit. Open full-size diagram. Technical reference.

What belongs in the panel request

  • Machine and motor identification, supply details and the operating modes that can command a run.
  • The equipment and motion affected by each emergency stop station and any connected equipment that affects the same hazard.
  • The required stopping behaviour, expected post-stop condition and any energy that remains present.
  • Reset behaviour and the separate action required for a permitted restart.
  • The responsible designer, drawing revision and validation documents requested at handover.
  • Details of normal interlocks, remote controls and retained run requests that affect the complete system.

VUKAR's three-phase DOL panel comparison identifies standard models and their ordinary control features. The VUKAR product catalogue lists the TPM-A as a DOL panel with auto switch and cyclic timer. Those descriptions can help specify ordinary motor operation. For a machine safety function, ask for the exact circuit documentation and the complete machine validation relevant to the application.

Which parts of the machine are included?

Consider two conveyor sections with a transfer point between them. Each section can run alone during cleaning or maintenance. During production, the first feeds the second. An emergency stop next to the transfer point may need to affect equipment on both sides. The machine designer should define the response and explain how it works in each permitted mode. A generic panel label cannot settle that scope. A simple sketch with the operator positions and the affected machines helps the panel supplier quote the right interfaces.

Ask how the safety function deals with the faults considered in the design. For example, if the stopping path relies on a contactor opening, the designer needs to consider what happens when that contactor fails to open. The required architecture and monitoring depend on the risk assessment, the applicable standard and the hardware. The solution needs to be validated in the complete machine. An extra pushbutton on the enclosure does not establish that result.

Do the same for any pneumatic, hydraulic or stored mechanical energy that can still move the equipment. The safety response can include a coordinated action across more than one source of energy. Specify the condition the operator should expect after the response completes. If servicing is needed, follow the separate isolation procedure for all relevant sources.

What a useful handover record shows

Ask the responsible specialist to show the result for each emergency stop device and the relevant operating modes. The record should name the initiating station, the expected response, the actual response and what happened at reset. A result such as “E-stop OK” leaves out the information needed when a second station is added or the machine control changes.

Include the drawing revision and the date of the test. If the emergency stop acts on linked machines, the record should name which machines were involved. Keep the evidence with the machine documentation so the person who maintains it later can see what was designed and what was actually validated. Equipment faults and foreseeable failures require specialist assessment rather than an operator improvising a test on a working machine.

Revisit the validation scope when a new remote start station, an upstream controller or a second machine is added. Those changes can alter who has permission to start and which units stop together. Make sure the maintenance team receives the new documents and any change to the operator procedure before the machine returns to service.

Acceptance test record
Acceptance test record. Record the expected response and evidence for each station and applicable mode. · Open full-size visual

One question to ask before signing the quote

Ask the supplier to write one complete example in plain words. “While the machine is in Auto and its remote run request is active, an operator uses the emergency stop at the loading point. This equipment stops in the specified way. After the button is reset, the machine remains in its defined state until this deliberate action permits restart.” Ask them to name the affected equipment and fill in the two responses.

If the answer depends on another supplier's controller or site wiring, write that interface into the scope. The person accepting the machine should receive a clear description of the actual operation, the drawings and the associated validation record. That gives the operator a usable procedure and the maintenance team a traceable basis for future work.

Back to blog

Leave a comment

Please note, comments need to be approved before they are published.