Transparent electromechanical relay on an electronics workbench

Relay कैसे काम करता है: Interactive Pump Starter Fault Simulator

Mohit Vekaria

Relay एक control signal से दूसरे circuit के contacts खोलता या बंद करता है। Pump panel में float या controller, relay को switch करने का संकेत दे सकता है। Protection circuit इजाज़त दे तो relay, motor को power देने वाले contactor को command देने में मदद करता है। नीचे के simulator में देखें कि start request कहाँ रुक सकती है।

CoilElectromagnetic relay में हरकत पैदा करती है।
ContactsRelay चलने पर खुलते या बंद होते हैं।
Contactorइस उदाहरण में motor की power switch करता है।

NO और NC contacts में क्या होता है?

NO का मतलब normally open और NC का मतलब normally closed है। आम non-latching relay में normal का मतलब coil off की स्थिति है। Coil energise होने पर changeover contact, NC से NO पर जाता है। Terminal marking समझने से पहले अपने relay का diagram देखें।

छोटी screen पर और कॉलम देखने के लिए टेबल को बगल में सरकाएँ।

एक आम changeover relay
Coil की स्थिति COM से NO COM से NC
Off खुला बंद
On बंद खुला

OMRON relay contacts और संचालन गाइड

Pump starter fault simulator आज़माएँ

Reference case खोलें, फिर चार faults में से कोई एक खोलें। Tank request से motor तक control states क्रम से देखें। इस उदाहरण में interposing relay, overload permissive और contactor है। असल क्रम और indications आपके panel पर निर्भर हैं।

Reference case — tank से पानी की माँग आती है
Tank requestमिली
Control relayCoil on · NO contact बंद
Overload protectionStart की अनुमति
Contactor commandOn
इस simulation में motorचल रही है

Control relay का contact बंद होता है, protection start की अनुमति देती है और contactor खिंचता है। यह सीखने वाले circuit का सामान्य run sequence है।

अपेक्षित request, relay, protection और contactor की स्थिति अपने panel के indicators से मिलाएँ।

Case 1 — tank का level कम है पर panel तक request नहीं पहुँचती
Tank requestनहीं मिली
Control relayCoil off · NO contact खुला
Overload protectionStart की अनुमति
Contactor commandOff
इस simulation में motorबंद है

Sequence relay से पहले रुकता है। Panel को start request नहीं मिली। असल system में selected mode, sensor input, float या उसका cable कारण हो सकता है।

Electrician को actual tank level, selected mode और panel का demand indicator बदलता है या नहीं, बताएँ।

Case 2 — request आती है पर relay coil off रहती है
Tank requestमिली
Control relayCoil off · NO contact खुला
Overload protectionStart की अनुमति
Contactor commandOff
इस simulation में motorबंद है

Model में request और relay coil के बीच रुकावट है। Normally open contact खुला रहता है। Contactor को start command नहीं मिलती।

नोट करें कि demand indicator on है या नहीं और relay indicator बदलता है या नहीं। Electrician से panel diagram के अनुसार relay control path और coil supply जँचवाएँ।

Case 3 — relay switch करता है पर overload start रोकता है
Tank requestमिली
Control relayCoil on · NO contact बंद
Overload protectionTrip हुआ · command रोकता है
Contactor commandOff
इस simulation में motorबंद है

Relay contact बंद होता है। Tripped overload protection path खोल देता है, इसलिए contactor command off रहती है। यहाँ overload indication पहला संकेत है।

दिखा fault code और उसका समय नोट करें। Electrician दोबारा चालू करने से पहले trip का कारण जाँच सकता है।

Case 4 — contactor को command मिलती है पर वह खिंचता नहीं
Tank requestमिली
Control relayCoil on · NO contact बंद
Overload protectionStart की अनुमति
Contactor commandOn
इस simulation में motorबंद है

Model start command दिखाता है लेकिन contactor नहीं हिलता। केवल command indication से तय नहीं होता कि सही coil voltage contactor तक पहुँचा।

Request, protection और command indications बताएँ। यह भी बताएँ कि contactor हिला या click हुआ। Electrician से coil circuit और contactor की जाँच कराएँ।

घटना बताने के लिए display, labels और बाहर से दिखने वाले indications का इस्तेमाल करें। अंदर के terminals जाँचने से पहले qualified electrician circuit isolate करे और पुष्टि करे। सभी protective functions चालू रखें।

रिले, कॉन्टैक्टर और सुरक्षा जांच के अलग चिह्न
पंप स्टार्टर में रिले, कॉन्टैक्टर और सुरक्षा उपकरण के काम अलग हैं।

Relay, contactor या overload device?

छोटी screen पर और कॉलम देखने के लिए टेबल को बगल में सरकाएँ।

कौन-सा भाग क्या करता है?
भाग इस उदाहरण में काम क्या मिलाएँ
Control relay Control command आगे भेजता है। Coil voltage और AC/DC type, contact configuration और control-load rating।
Contactor Motor supply switch करता है। Supply voltage पर motor duty rating, motor current और coil supply।
Overload device लंबे overload के trip के बाद run रोकता है या शुरू नहीं होने देता। Motor nameplate current, trip characteristics और starter design।

Fault बताते समय starter model, motor nameplate, operating mode, दिखा fault और sequence में जहाँ indication बदलना रुका वह point बताएँ।

Contactor चयन और terminal guide पढ़ें · Contactor के बार-बार click के लक्षणों की तुलना करें

छोटे जवाब

क्या relay का click साबित करता है कि contacts ठीक हैं?

Click से हरकत का संकेत मिलता है। Technician सही test method से संबंधित contacts और अगला control stage जाँच सकता है।

क्या सिर्फ़ amp rating से replacement relay चुन सकते हैं?

Coil voltage, AC/DC type, contacts, load type, terminal arrangement और device की switching ratings जाँचें।

ब्लॉग पर वापस जाएं