Illustration of a Rajpura farm with a submersible pump, a motor starter and a separate power connection

Submersible Pump Starter Panel Supplier in Rajpura

Mohit Vekaria

If you need a Submersible Pump Starter Panel Supplier in Rajpura, compare VUKAR TPM-A from SubmersibleShop.com for a compatible three-phase pump that uses direct-on-line starting. If the new motor has a higher power rating, check the approved load on your farm connection before you buy it. A starter sold for a larger motor does not change the power load listed for your connection.

Check the Rajpura farm pump load

Punjab State Power Corporation’s South Zone directory lists its Rajpura distribution division under Patiala. A PSPCL example form for an agricultural tubewell load change separates the load already approved from the load the farmer wants to add. The form is from 2024. Ask the division that serves your connection for the current process and the load on your own record. Use the account details from your bill when you speak with the utility.

Make two columns on your job sheet. Write the old motor and connection details on the left. Write the proposed motor on the right. If the old motor failed, ask the pump installer to confirm its original duty before ordering a larger one. Duty is the job the pump has to do, such as lifting water to a tank or supplying a field pipe. A larger motor does not tell you how much water the well can supply. If the farm has two connections, identify which one feeds this pump. Write the pump name next to the connection on your private job sheet so the installer checks the right one.

Diagram showing the supply record, motor plate and starter label as three separate checks
The motor and starter ratings must match the job. The utility confirms the connection load separately.

Read the submersible pump motor plate

The motor plate is the label with its electrical details. Ask the electrician to record its HP, voltage, phase and rated current. HP means horsepower. It is a unit of power. Current is measured in amps. If the motor is down the borewell and the label is not visible, use the original manual or ask the installer to identify it safely. A handwritten number on the old panel may describe that panel and not the pump.

Worked example · A 5 HP to 7.5 HP proposal

Assume your connection record lists 5 HP and the installer proposes a 7.5 HP motor. A starter rated for up to 7.5 HP can be an option only after the supply and start method are checked. The 7.5 HP label on the panel does not change the 5 HP record. Treat the two figures as example values.

What to check Where to find it
Approved connection load Utility record for the farm connection
Motor voltage, phase and current Motor plate or maker’s model sheet
Correct starter type and variant Electrician’s assessment and product page

Keep the details of the old and new motor apart. Ask how the present motor starts. If a drive controls it or the old starter starts it in stages, a simple DOL starter may not be the right replacement. Check who will verify cable size, supply capacity and the starting method before anyone orders the new motor.

When a three-phase DOL pump starter fits

The VUKAR TPM-A product page lists direct-on-line starter variants up to 10 HP for compatible pumps. Direct-on-line, or DOL, means the starter applies the full supply voltage to the motor at start. Confirm the exact variant and motor protection settings with the electrician. Ask what will happen when power returns after a cut. Put that response on the job sheet so it can be tested when the panel is fitted.

What to send for a Rajpura submersible pump quote

Send the new motor plate or model sheet, the old starter label and the installer’s confirmation of the starting method. Tell VUKAR whether you are replacing the same motor or changing the power rating. Keep your utility account details with the utility. Ask the panel supplier to list the starter, fitting and handover test separately. Have the installer show a normal start and stop and record the fitted model next to the pump tag. Ask the electrician to date the test and leave the protection settings with the pump record.

Open the three-phase DOL starter comparison and send VUKAR the motor and starter details. If the motor size is changing, get the connection check first and share the final motor choice when you ask for a quote.

Back to blog