Insulation resistance tester beside a disconnected motor on a workbench

Megger Test: उद्देश्य, प्रक्रिया और Insulation Resistance Readings

Mohit Vekaria

Megger test, DC insulation tester से insulation resistance को megohms में मापता है। Motor में यह नमी, गंदगी या damaged insulation से बने leakage paths पहचानने में मदद करता है। Reading की तुलना motor निर्माता के criteria और मिलती-जुलती स्थितियों में ली गई पिछली readings से करें। एक reading समझने के लिए उसका test voltage, duration और temperature भी चाहिए।

MΩMegohms। Insulation resistance बताने की इकाई।
Test voltage और समयदोनों दर्ज करें क्योंकि इनका reading और उसके अर्थ पर असर पड़ता है।
तापमानतय correction लगाएँ या मिलती-जुलती स्थितियों में तुलना करें।

Insulation test क्या बताता है

और कॉलम देखने के लिए टेबल को बगल में सरकाएँ।

अपने सवाल का जवाब देने वाला test चुनें
Test क्या जाँचता है
Insulation resistance Insulation से होकर leakage paths, जैसे motor windings और frame के बीच।
Winding resistance Windings का electrical resistance। तुलना से असंतुलन या connection की समस्या का पता चल सकता है।
Earth-bond continuity Protective bonding path में ज़रूरी continuity है या नहीं।

Motor, drop cable और joints की साथ जाँच करने पर इनमें से हर भाग कम reading का कारण हो सकता है। जहाँ connections तक पहुँच हो वहाँ हिस्सों को अलग test करने से fault की जगह ढूँढने में मदद मिलती है। सही insulation resistance reading से हर winding fault, जैसे कुछ interturn faults, की संभावना खत्म नहीं होती।

Megger insulation testing गाइड · Megger motor test functions

Test से पहले और बाद में technician क्या जाँचता है

  1. Isolate करें और पुष्टि करें। Qualified technician motor isolate करता है, दोबारा start होने से रोकता है और पुष्टि करता है कि voltage नहीं है।
  2. Sensitive equipment अलग करें। निर्माता की प्रक्रिया के अनुसार drives और sensitive electronics को test path से disconnect करें। पहचानें कि measurement में cable, motor या दोनों शामिल हैं।
  3. तय तरीके से test करें। उस equipment के लिए DC test voltage, connections और test duration चुनें। Result के साथ motor temperature और स्थितियाँ दर्ज करें।
  4. Discharge करें और रिकॉर्ड रखें। Test के बाद circuit discharge करें और terminals छूने या equipment फिर जोड़ने से पहले पुष्टि करें कि यह सुरक्षित है। Reading और ठीक कौन-सा हिस्सा test किया, दर्ज करें।

Insulation testing से पहले drive अलग करने पर निर्माता के निर्देशों का उदाहरण

टेस्टर, रिकॉर्ड शीट और आवर्धक कांच के चिह्न
मापे गए इंसुलेशन प्रतिरोध की तुलना मोटर निर्माता के मानदंडों से करें।

Result कैसे पढ़ें

एक motor की readings का उदाहरण

120 MΩ → 85 MΩ → 28 MΩ

अगर एक ही हिस्से को मिलते-जुलते temperature, voltage और duration पर मापा गया हो तो घटती readings की जाँच करें। Service तय करने से पहले motor निर्माता की limits से तुलना करें और cable, terminations व windings जाँचें।

मापे गए MΩ, test voltage, duration, temperature और test किए गए भाग की जानकारी माँगें। Pump ज़मीन के नीचे है तो पूछें कि reading में downhole cable और motor दोनों शामिल हैं या नहीं। इससे पता चलता है कि repairer उस result से क्या निष्कर्ष निकाल सकता है।

Submersible pump repair गाइड

छोटे जवाब

क्या हर pump motor की एक ही pass value होती है?

उसी motor के लिए निर्माता के criteria, तय test method और temperature आधार इस्तेमाल करें। किसी अलग motor या test setup की संख्या गलत निष्कर्ष दे सकती है।

क्या multimeter megger test की जगह ले सकता है?

Multimeter का resistance mode बहुत कम test voltage इस्तेमाल करता है। Qualified technician तय DC test के लिए उपयुक्त insulation tester इस्तेमाल करता है।

Motor चलती है लेकिन starter fault दिखाता है तो तुलना करें dry-run और overload के लक्षणों की.

ब्लॉग पर वापस जाएं