Two closed water storage tanks on separate bases in a shared courtyard.

2,000 Litre Water Tank Prices for Shared Homes

Mohit Vekaria

Published examples for 2,000 L Sintex tanks ranged from ₹14,479 to ₹23,925 across three named models when checked on 10 November 2026. For two homes, compare a single 2,000 L tank with two smaller tanks. Access, valve layout and what stays in service during cleaning can decide the better fit.

Shared-home storage

Choose the setup you can keep running

  • One 2,000 L tankOne vessel to monitor. Plan how both homes get water during cleaning.
  • Two smaller tanksMay be easier to move in and isolate. Budget for extra valves and connections.
  • About 2 tonnesTotal water load at full capacity before tanks, fittings and supports.
Sintex Reno white double layer
Displayed tank price. ₹14,479
Sintex black double layer CCWS-200.01
Displayed tank price. ₹19,200 including tax on the product page
Sintex Pure white triple layer
Displayed tank price. ₹23,925

Will the 2,000 L tank make the turn?

The black CCWS-200.01 listing gives a body diameter of 1,327.5 mm and a height of 1,572.5 mm. Another 2,000 L white model is listed at 1,400 mm diameter and 1,560 mm high. A difference of 72.5 mm in width can matter at a landing or inside a service opening. Get the manufacturer’s drawing and have the supplier confirm the delivery route before you pay.

One family might have enough space for a 2,000 L tank but no way to bring it past a tight roof hatch. The installer may find that two smaller tanks can reach the roof more easily. That changes the plumbing, valves and cleaning plan. It also changes where the loads fall. Have a qualified person assess both layouts before choosing.

Think about who shares the water

Suppose two households use 650 L each between refills. With 300 L for a late supply, the target is about 1,600 L of usable water. A nominal 2,000 L tank is worth comparing, provided the actual usable capacity covers that target.

For shared use, decide who pays for water and pump maintenance, who can isolate a tank, and how people will know there is a fault. Separate tanks can make isolation easier in some designs. A shared tank can make the storage and level easier to manage in others. Ask the plumber to draw what stays in service when a valve or tank is shut.

Practical example

What happens when one tank is taken offline?

In an illustrative split system with two 1,000 L tanks, taking one offline leaves at most 1,000 L of nominal storage. If both homes need 1,300 L before the next refill, that is already a 300 L gap before usable-volume losses. Agree a low-demand cleaning window or a temporary supply plan. A split system is only useful if the pipework lets the remaining tank serve the intended homes.

Compare the full cost

A Plasto 2,000 L quote is useful when it names the series and dimensions from the Plasto catalogue, with the lid, fittings and warranty written down. Compare it with the same-capacity Sintex quote at the same address. Include freight, lifting, base work, valves and labour.

Keep the first month simple

Write down one normal refill time and note which valve feeds each home. If a family later reports that one floor is running out of water early, the plumber can compare the new behaviour with the original setup. Leave the dated drawing near the pump panel or with the building’s maintenance records, where both households can find it.

Ask for a service sketch

Have the installer show the isolation valves, which home each outlet serves, and how to keep one tank in use when the other is cleaned.

At full nominal volume, the tank holds roughly two tonnes of water. Confirm its base and the building’s support with the right professional. Then check your planned refill window. At a measured 35 L per minute, replacing 1,200 L takes about 34 minutes if nobody draws water during the fill. Run your actual numbers in the tank calculator.

Sources

ब्लॉग पर वापस जाएं